Washing Machine Repair in Abu Dhabi

Shozi Home Appliance Repairs provides washing machine repair in Abu Dhabi with home visits for front-load, top-load and washer-dryer machines. Technicians inspect draining, spinning, leaking, door-lock, noise and error-code faults at your home in Abu Dhabi City, Mussafah, Khalifa City, Mohammed Bin Zayed City, Al Reem Island, Yas Island, Saadiyat Island and Al Raha Beach.

Send us a message

Shozi appliance repair service in Khalifa City

Safety note: Stop using the washer if it is actively leaking near electricity, producing a burning smell, sparking, severely overheating, or moving violently enough to damage nearby fittings.

Request help for washers that will not start, fill, drain, spin, unlock, or complete a cycle, as well as leaks, shaking, unusual noise, poor washing results, and recurring error codes.

Send your area, exact location, washing machine type, brand, model number if safely accessible, reported symptom, error code, and preferred appointment time. A clear model-label photo or short video of an unusual sound may help when it can be captured safely.

Service hours are 9:00 AM–8:00 PM UAE time. Appointment timing and possible same-day attendance depend on the request time, location, suitable technician availability, appliance details, and the day’s route.

Diagnosis Before Repair

Approval Before Work

Residential Home Visits

Clear Parts Guidance

Diagnosis for Washing Machine Faults

The visible symptom does not always identify the failed part. A no-spin complaint may begin with an unbalanced load or drainage problem, but it can also involve the door lock, motor system, drive components, sensors, wiring, or controls.

A washer that will not fill may have a supply issue, blocked inlet screen, valve fault, pressure-sensing problem, or control issue. Diagnosis starts by confirming what the machine does at each stage of the cycle.

Depending on the reported fault and appliance design, the technician may inspect accessible hoses, filters, the door or lid mechanism, drainage path, inlet system, suspension, drive system, wiring, sensors, and controls. Parts should be recommended only after the likely cause has been identified.

Washing machine repair technician inspecting a washer in Abu Dhabi

Common Washing Machine Symptoms We Investigate

Different faults can produce similar symptoms, so the list below should be used as booking guidance rather than as a final diagnosis.

Washer Will Not Start

Possible causes include the power supply, door or lid lock, control settings, wiring, safety switches, sensors, or electronic controls.

Water Will Not Drain

Standing water may relate to a kinked hose, user-accessible filter blockage, pump restriction, failed pump, sensor issue, wiring fault, or control problem.

Drum Will Not Spin

A no-spin fault may involve an unbalanced load, incomplete drainage, door-lock confirmation, drive parts, motor system, sensors, wiring, or controls.

Washing Machine Is Leaking

Leaks may come from hoses, connections, the door seal, detergent dispenser, drain pump, tub, or internal pipework.

Shaking or Unusual Noise

Excess movement or noise may result from loading, levelling, transit hardware, suspension wear, bearings, drive parts, or structural damage.

Error Code or Incomplete Cycle

Record the exact code and the stage when it appears. An error code is a diagnostic clue and should be assessed with the machine’s actual behaviour.

Washing Machine Brands We Repair in Abu Dhabi

We repair washing machines from the brands most common in Abu Dhabi homes, including LG, Samsung, Bosch, Siemens, Whirlpool, Ariston, Beko, Teka, Midea and Hitachi. Front-load and top-load models are both covered, as well as washer-dryer combinations.

When you book, send the brand and the model number from the label inside the door or on the back panel. This helps the technician check common faults and parts availability for your machine before the visit.

LG and Samsung washing machine repair:
drain pumps, door locks, inverter and control faults, error codes
drainage, heating, bearing noise, door and program faults
Other brands:
share the model and the fault so the visit can be planned correctly

Front-Load, Top-Load and Washer-Dryer Repair

Front-load washing machines often come in with door-lock faults, blocked drain filters, worn door seals, bearing noise and spin problems. Top-load machines more often have lid-switch, agitator, drive and unbalanced-load faults. Washer-dryers add drying faults such as no heat, long drying times or condenser blockages.

Tell us which type you have when booking, together with what the machine does when the fault appears: for example, whether it fills but does not drain, drains but does not spin, or stops at the same point in every cycle.

Washing Machine Error Codes We Fix

Modern washing machines show an error code when they stop. The code points to the area of the fault, not always the failed part, so a technician still checks the machine before replacing anything. Common codes we diagnose and repair include:

LG washing machines:
OE (water not draining), IE (water not filling), UE (unbalanced load), dE (door not locking), LE (motor locked or overloaded), FE (overfill), PE (water level sensor), tE (heater or temperature sensor)
Samsung washing machines:
5C / 5E / nd (drain fault), 4C / 4E (water supply), UB / UE (unbalanced load), dC / dE (door lock), 3C / 3E (motor), HC / HE (heating), LC / LE (water leak), 1C / 1E (water level sensor)
Bosch and Siemens washing machines:
E18 / F18 (draining), E17 / F17 (water inlet), E23 / F23 (leak detected in the base), F21 / E21 (motor or drum blocked)

Codes differ between models and model years, so check your manual and send us the exact code with the model number. Never keep restarting a machine that shows a leak or motor code.

Safe Checks Before Booking

Before requesting service, check only the items that can be inspected safely without moving the machine or removing panels.

  • Confirm that the power outlet is working only if the area is dry and safe.
  • Check that the water taps are open and visible inlet hoses are not sharply kinked.
  • Confirm that the door or lid is fully closed.
  • Check whether the selected program includes a spin cycle.
  • Redistribute a single heavy item or severely unbalanced load.
  • Use the correct amount and type of detergent because excess suds can interfere with draining or spinning.
  • Check the visible drain hose for kinks without pulling out a heavy or built-in machine.
  • Clean a pump filter only when the manufacturer identifies it as user-accessible, the washer is unplugged, the water is cool, and retained water can be contained safely.
Stop immediately if access requires removing panels or approaching water near electrical parts.
Washing machine repair technician inspecting a washer in Abu Dhabi

What the Technician May Check

Inspection depends on the reported symptom, appliance design, accessibility, and safe working conditions.

Operating Stage

The technician may confirm whether the fault occurs during filling, washing, draining, spinning, unlocking, or cycle completion.

Water Inlet and Drainage

Accessible hoses, filters, pumps, valves, drainage paths, pressure sensing, and related connections may be inspected where relevant.

Door, Lid, and Lock System

The door or lid mechanism, lock confirmation, wiring, and related safety controls may be checked when starting or spinning is affected.

Drum, Drive, and Suspension

Suspension, drive components, motor system, bearings, and structural movement may be assessed when the washer shakes, makes noise, or will not spin.

Wiring, Sensors, and Controls

Relevant wiring, sensors, switches, and electronic controls may be evaluated when symptoms point to an electrical or control-related fault.

Post-Repair Testing

After approved work, the original symptom and basic cycle functions are checked where the water supply, drainage, installation, and safety conditions allow.

Preparing for a Washing Machine Repair Visit

Have the brand and model number ready when possible. A clear model-label photo can help identify the appliance, but it does not replace diagnosis.

Clear laundry and obstacles from around the washer and ensure an adult can provide access. Share parking, reception, security, lift, or building-access instructions where relevant.

Do not pull out a heavy, built-in, leaking, gas-adjacent, or electrically unsafe machine. Tell the technician about previous repairs, intermittent faults, unusual sounds, smells, leaks, and the stage of the cycle when the problem occurs.

If a component is required, availability depends on the model, supplier, and compatibility. A follow-up visit may be required.

Residential washing machine repair visit in Abu Dhabi

Repair or Replace the Washing Machine?

Repair may be worth considering when the cabinet, tub, and main structure remain in reasonable condition and the fault is limited to an identifiable component with suitable parts available.

Replacement may be more practical when the machine has serious corrosion, repeated major failures, structural damage, multiple failing systems, unavailable components, or a repair cost that is high compared with its age and condition.

Energy and water use, capacity requirements, previous repair history, and the likelihood of another significant fault are also relevant. The inspection findings, proposed work, expected cost, and parts situation should be explained so the customer can compare the options.

How Washing Machine Repair Appointments Work

One clear four-step process takes the request from booking to approved work and a conditional functional check.

1. Send the Washer Details

Share the washer type, brand, model, reported symptom, exact error code, location, access details, and preferred appointment time.

2. Confirm Coverage and Timing

The request is reviewed against the published service scope, exact location, suitable technician availability, route, and access requirements.

3. Inspect and Explain the Fault

The technician assesses the reported problem and explains the likely cause, proposed repair, expected cost, and parts situation before work proceeds.

4. Complete and Test Approved Work

After approval, the agreed work is completed and the original symptom and basic washer functions are tested where installation, water, drainage, and safety conditions allow.

Washing Machine Service Areas

Washing machine repair appointments are arranged across Abu Dhabi, subject to the exact location, route, technician availability, appliance information and access requirements. For local details, see washing machine repair in Mussafah and Shabiya or washing machine repair in Khalifa City.

Request Washing Machine Repair in Abu Dhabi

Call or WhatsApp +971 50 581 8026 between 9:00 AM and 8:00 PM UAE time.

Send your area, exact location, washer type, brand, model number if available, reported symptom, error code, building-access information, and preferred appointment time.

Do not run another test cycle if the machine is actively leaking near electricity, producing a burning smell, sparking, severely overheating, or moving violently.

A washer can stop spinning because the load is unbalanced, water has not drained, the selected program limits spin, the door lock has not confirmed safe closure, or there is a fault in the drive, motor, sensor, wiring, or control system. Redistribute an unusually heavy load and check whether the machine has drained. Persistent failure needs inspection.

Check for a kinked visible drain hose and clean only the user-accessible filter described in the model manual. Be prepared for retained water and stop if panels must be removed. A blocked pump, failed pump, hose restriction, sensor issue, wiring problem, or control fault may require service.

Leaks may come from hoses, connections, the door seal, detergent dispenser, drain pump, tub, or internal pipework. Stop the cycle and disconnect power safely if water could reach electrical parts. Note whether the leak occurs during filling, washing, or draining.

Redistribute an unbalanced load and confirm the washer is level and stable. A newly installed machine should also have transit hardware removed according to the installation instructions. Persistent banging, movement, grinding, or roaring may involve suspension, bearings, drive parts, or structural damage.

Record the exact code and when it appears. An error code is a diagnostic clue, not always a final diagnosis. Avoid repeated resets if the machine is leaking, overheating, or making abnormal sounds.

Same-day attendance may be possible when the request time, location, suitable technician availability, and the day’s route align. It is confirmed at booking and is not guaranteed.

Pricing depends on the diagnosed fault, machine design, access, labour, and required parts. Two machines with the same symptom may need different repairs, so a firm price is normally based on inspection. The proposed work and expected cost are explained before approved work begins.

Repair may be sensible when the washer is generally sound, the fault is limited, and suitable parts are available. Replacement may be more practical when there is serious corrosion, repeated failure, major structural damage, unavailable components, or a repair cost that is high relative to the machine’s age and condition.

The cost depends on the fault, the machine type and brand, access and any parts needed. A drain-filter blockage costs far less than a drum bearing or control-board repair. The technician diagnoses the machine first and explains the repair and expected cost before any work begins.

Yes. We repair LG, Samsung, Bosch, Siemens, Whirlpool, Ariston, Beko, Teka, Midea and Hitachi washing machines, including front-load, top-load and washer-dryer models. Send the brand, model and any error code when you book.

Other Home Appliance Repair Services

Choose another appliance category for service-specific guidance.

Refrigerator and Freezer Repair

Inspection and repair guidance for poor cooling, unwanted freezing, water leakage, frost buildup, unusual noise, cycling concerns, and door-seal problems.

Dishwasher Repair

Help with standing water, poor cleaning, leaks, no-start faults, incomplete programs, unusual noise, and recurring dishwasher error codes.

Stove and Cooktop Repair

Repair guidance for gas or electric stoves and cooktops with ignition, heating, temperature-control, switch, control-panel, or wiring concerns.